14g or 12g Micro Dermal or Labret or Barbell Steel EXTENSION POST

Material is 316L ASTM F-138 Implant Grade Stainless Steel. You are only buying 1 End. You will need to buy the anchors separately.

Use with our MicroDermal Anchors or Internal Labret Posts & Straight Barbells

Thread length is 2mm. Total length is 2.5mm. Thread pattern is 1.2mm.

Made from 1 solid piece of material. Great if your just need to extend a barbell only a couple of millimeters or raise an anchor that is to deep. Extension Post has 1.2mm thread pattern on one end and is tapped to allow 1.2mm threaded ends.

Healing post for micro dermal implants. 1.2mm threading. Good for allowing the implant to heal before changing to ball, jewel, spike, etc.

Will also thread onto any internal jewelry in 14g or 12g with a 1.2mm thread pattern.

Price is per post. Dermal not included.

2.5mm Long 1.6mm thick Thread pattern is 1.2m

Saferly Ultra Fine Tip Surgical Skin Marker. This pens tip won't clog and stays needle sharp - yet soft enough to insure patient safety!

The ink is gentian violet. It is a surgical ink that is the only ink approved for use on human skin during any invasive procedures.

It can be removed with alcohol and a gentle scrub. It becomes a more permanent mark once it is allowed to dry. The pen is non-sterile and aseptic.

Do not autoclave. It will melt!

It is, as all pens like this are, intended for single patient use. The barrel doesn't need to be sterilized because it shouldn't be coming into contact with the wound site. The tip has never touched skin, so as long as it is single patient use, there is no chance for cross-contamination. The pen should be discarded or given to the client after use.

Price is for one - Quantity discounts are available.

Directions for Use:

1. Clean skin area thoroughly with an alcohol prep or swab. Dry the area completely.
2. Carefully mark the cleaned skin area. Allow skin markings to dry.
3. Prep normally over marked site.
4. Use alcohol and a gentle scrub to remove markings.

Threaded Taper for Internally threaded Jewelry, Dermal Anchors, etc..

Taper is 14g at its thickest point and has a 1.2mm thread on the end.

Use these to insert internally threaded jewelry or your dermal anchors. The size of the taper is the thickest part. Measures 4 inches long.

Spirit brand blue carrier sheet. Protects stencil paper and lengthens life of your thermofax

Thermofax machines tend to develop 'hot spots' as they are used over and over. Using this Spirit brand blue thermofax carrier spreads the thermal energy evenly over the entire transfer paper, helping to get rid of the “burns” that occur. It also helps to reduce over and underexposure which allows you to get and even, clear stencil.

Size is approximately 8-5/8" x 14.5"

Please Note: Blue Carriers are designed for use with older 3M thermal machines. If you have the Panenka Thermal Imager or other A3/A4 thermal machines, it is recommended to use a Clear Carrier.

14g 3/8" curved navel bar.

Ball and curved bar are 316L surgical implant grade steel

All other casting parts(charms, dangles, etc) are Rhodium plated over Brass or Copper

Tweezer style triangle end forceps with locking mechanism.

Great alternative to regular forceps due to being lighter and smaller than regular forceps. Easy to use with one hand. 

These tweezer forceps are approximately 5-3/4". They have a 12mm head with a 7mm inner hole diameter.

These forceps are only available without slots.

4-1/2" tweezers with end designed to hold a ball or bead snugly.  Great for picking small balls and beads out of loose jewelry bins or displays.

Bag of 100 5" x 8" spray bottle/wash bottle covers.

Open on one end, sealed on the other.

Protects your bottles from fluids and splatter.

Low density and meets the FDA requirements for food storage.

Bag of 100 5" x 6" tattoo machine covers.

Open on one end, sealed on the other.

Protects your machine from fluids and splatter.

Low density and meets the FDA requirements for food storage.

490 ml (16.5oz) bottle of Talens black Indian Ink.

Be advised: the bottle specifically says NOT for tattooing. 

Manufactured by Royal Talens.

Talens ink is the richest dark, black ink ideal for outlines and tribal designs, but also easy to dilute for gray shading work. It is one of the most popular, darkest and most requested drawing inks in the industry. Gives an attractive deep black result through a maximum pigment concentration. Can be thinned with water. Talens indian ink and drawing ink are used by master tattoo artists around the world.

Standard clip cord for tattoo machines. 8 ft. clip cord with 1/4" phono jack plug.

Available in black.

Alconox ultrasonic detergent. 4lb Container powedered detergent concentrate.

This will make up to 52 gallons of ultrasonic solution.

This is one of the preferred brands of cleaners used in ultrasonics for soaking of tattoo and piercing equipment. Alconox is a dry powder. When diluted with distilled water his cleaner effectively loosens dried tattoo ink, blood, soft tissue and the like from your instruments. Once soaked, instruments are then ready to be autoclaved.

Pelikan Drawing Ink is designed for art, school and hobby.

Waterproof ink for drawing and painting. Especially suitable for ruling pens, technical pens, dip pens and brushes. Clearly labeled not for tattooing.

Bend the perfect nostril screw every time! Over the years we have heard many piercers ask for either shorter or longer nostril screws, or screws with more acute or obtuse bends on the end.

This tool eliminates those problems. Use this tool with out U-Bend nostril pins.

You pick the wearable area, and the degree of the screw bend. Scroll down for detailed instructions on how to use this item.

Crafted from 410 ASTM Stainless Steel.