14g and 12g Thin Jeweled Disc Top for Internally Threaded Jewelry. Use with our MicroDermal Anchors or Labret Post

Material is 316L ASTM F-138 Implant Grade Stainless Steel. You are only buying 1 end. You will need to buy the jewelry to attach it to separately.. Thread length is 2mm. Thread pattern is 1.2mm which means you can use on a 14g or 12g barbell piece of body jewelry that uses this thread pattern. Made from 1 solid piece of material

18g–16g Stainless Steel Jewel Ball — Pick Jewel Size and Color — Internal 0.9mm

These steel jewel balls for 18g and 16g internally-threaded body jewelry are available in 16 colors and 4 sizes, including 1.5mm, 2mm, 2.5mm, and 3mm. Each ball and its internal 0.9mm threaded post are made from a single piece of surgical stainless steel with a bezel-set jewel. You can use these replacement jewel balls with any 18g or 16g internally-threaded body jewelry with a matching internal 0.9mm thread pattern.

The 18g–16g Internally Threaded Steel Jewel Ball is priced per one top.

Specifications

• Material: 316L ASTM F-138 Implant Grade Stainless Steel
• Jewel Size Options: 1.5mm–3mm (1/16”–1/8”)
• Threading: Internal 0.9mm
• 16 Jewel color options
• Price per one ball
• old sku: iSB-J-1618

Threadless Titanium Replacement Top - Plain Balll

0.45mm Threadless Shaft. Compatible with 0.5mm Threadless Jewelry

Change up the look of your jewelry quickly and easily

Over a hundred combinations to choose from!

How to Use Threadless Jewelry:

Threadless jewelry uses tension between the end and the shaft to fit and stay together. The end has an insertion pin which is slightly bent when inserted into a straight shaft. This slight bend of the pin against the straight shaft creates a spring tension, holding the end securely in place.

Follow the instructions below to secure the threadless end into the threadless shaft

1. Insert the pin one-third to halfway into the shaft.
2. Hand-bend slightly the insertion pin against the shaft.
3. Push the end into the shaft and test the fit.
4. Adjusting the Fit: If it is too tight, take some of the bend out of the pin and try again. Remember, adjust slightly and then try again.

14g to 8g Steel Replacement Ball for Externally Threaded Jewelry

These will thread onto any of our 14g, 12g, 10g, or 8g body jewelry with a matching external 1.6mm thread pattern.

Solid titanium half-ball which is currently available in 2, 2.5, 3 or 4mm. These can be used with any of our 18g to 16g jewelry with internal 0.9mm thread pattern.

Post length is approximately 1.5mm.  The ball is manufactured from exceptional quality, solid titanium, which makes it almost completely hypo-allergenic and lending itself to safe extended wear. Also comes in a number of jeweled colors AND anodized colors.

13mm, 14mm, 16mm or 19mm Counter-Sunk Steel Ball for 00g Internally-Threaded Body Jewelry (Price Per 1)

These counter-sunk steel balls and their posts with internal 2.0mm threading are each made from a single piece of 316L surgical stainless steel. They fit closely against the skin when paired with labret studs and other 00g internally-threaded body jewelry because of the way they're counter-sunk. This steel ball comes in 4 size options: 13mm, 14mm, 16mm, or 19mm.

These steel balls are sold individually (price per 1) and separately from our 00g internally-threaded labret studs, straight barbells and other body jewelry.

Specifications:

• Material: 316L Implant-Grade Stainless Steel
• Ball Size Options: 13mm (1/2"), 14mm (9/16"), 16mm (5/8"), or 19mm (3/4")
• Threading: Internal 2.0mm (3/32")
• Compatible With 00g Internally-Threaded Body Jewelry & Other Jewelry With Internal 2.0mm Threading
• Price Per 1 Counter-Sunk Steel Ball

Loose steel jeweled replacement balls - 2 sizes, 14 colors per size!

These will thread onto any of our 18g or 16g body jewelry with a matching external 1.2mm thread pattern.

Available in various sizes.

Material is 316L ASTM F-138 Implant Grade Stainless Steel.

You are only buying 1 End. You will need to buy your jewelry separately.

Use these with our microdermal anchors or labret posts.

Thread length is 2mm Thread pattern is 1.2m

Made from 1 solid piece of steel

316L ASTM F-138 Stainless Steel loose threaded balls. These will thread onto ANY of our 18g or 16g body jewelry with a matching external 1.2mm thread pattern.

11mm, 13mm, 16mm, or 19mm Steel Ball for 0g Internally-Threaded Body Jewelry

These counter-sunk stainless steel balls make great replacement balls for old, worn or lost body jewelry balls. Each ball with counter-sunk post is made from a single piece of surgical stainless steel that's been buffed to a high shine. The posts are inset to give you a closer fit; they're especially great when you have a dermal top or labret post that protrudes from your skin a little more than you'd like. The counter-sunk style allows you to screw the ball down so it's flush with your skin, making your jewelry appear to be a perfect fit!

These surgical steel balls are sold individually (price per 1) and separately from our body jewelry shafts and anchors. Their posts have an internal 2mm thread pattern, so you can use them with any of our 0g body jewelry that has matching internal 2mm threading. They're available in your choice of 4 sizes: 11mm, 13mm, 16mm, or 19mm.

Specifications:

• Material: Surgical Stainless Steel
• Ball Sizes: 11mm (7/16"), 13mm (1/2"), 16mm (5/8"), or 19mm (3/4")
• Threading: Internal 2mm (3/32")
• Wear With 0g Internally-Threaded Body Jewelry With Internal 2mm Threading
• Quantity: Sold Individually (Price Per 1)

Pick-up some of these countersunk, 316L implant-grade surgical steel balls to replace missing balls for any of your 6g internally-threaded body jewelry with an internal 2mm thread pattern.

Use them on straight, circular (horseshoes), curved barbells or any other style of jewelry with a matching thread pattern and gauge.

They're made of 316L surgical stainless steel, countersunk for a perfect fit every time, and available in your choice of 6mm, 8mm, 11mm or 13mm sizes.

Please note that these steel balls will only work with internally-threaded body jewelry with an internal 2mm thread pattern. Each surgical steel replacement ball is sold individually

Steel Disc available in 3mm,4mm, 5mm, 6mm, or 8mm sizes.

Perfect for any of our internally threaded jewelry with a 1.2mm thread pattern.
Material is 316L ASTM F-138 Implant Grade Stainless Steel
You are only buying 1 End. You will need to buy the jewelry separately.
Use with our MicroDermal Anchors or Labret Posts.
Thread length is 2mm
Thread pattern is 1.2m
Made from 1 solid piece of material

These surgical steel cones can be used as replacement tops on any of our 12g or 14g internally-threaded body jewelry that has an internal 1.2mm thread pattern.

Add one of these cones onto the end of your labret, use one with a dermal anchor, or even attach one to each end of a straight, curve, or circular (horseshoe) barbell.

Thread length is 2mm Thread pattern is 1.2m

Made from 1 solid piece of material

Jewelry sold seperately!

Threadless titanium cones made of synthetic opal

These eye-catching replacement pieces are compatible with all of our 18 gauge, 16 gauge, and 14 gauge threadless jewelry  

0.45mm Threadless 

Change up the look of your jewelry quickly and easily

Hundreds of color and size combinations to choose from

How to Use Threadless Jewelry:

Threadless jewelry uses tension between the end and the shaft to fit and stay together. The end has an insertion pin which is slightly bent when inserted into a straight shaft. This slight bend of the pin against the straight shaft creates a spring tension, holding the end securely in place.

Follow the instructions below to secure the threadless end into the threadless shaft

1. Insert the pin one-third to halfway into the shaft.
2. Hand-bend slightly the insertion pin against the shaft.
3. Push the end into the shaft and test the fit.
4. Adjusting the Fit: If it is too tight, take some of the bend out of the pin and try again. Remember, adjust slightly and then try again.

Fits 14g and 12g internally threaded jewelry or any internally threaded jewelry with a matching internal thread pattern.
You are only buying 1 End. You will need to buy the jewelry separately. Use with our MicroDermal Anchors or Labret Posts

• Titanium 6Al-4V-Eli ASTM: F-136. 
• Thread length is 2mm
• Thread pattern is 1.2m
• Made from 1 solid piece of material

18g - 16g Loose Steel External Thread Cone Ends.

Fits any piece of our jewelry from 16g to 18g.

External 1.2mm thread pattern.

Use with our MicroDermal Anchors or Labret Post.
Thread length is 2mm
Thread pattern is 1.2mm which means you can use on a 14g or 12g barbell piece of body jewelry that uses this thread pattern.
Made from 1 solid piece of material

Threadless Jewel Top - Pick Jewel Color and Size

This threadless flat opal top fits into many threadless jewelry pieces like labrets, barbells, and more. Wear it in a variety of body piercings. The top is made of high-quality titanium and, for a small fee, it can be anodized to one of 13 color options at our PainfulPleasures facilities in Hanover, MD. It boasts a flat jewel in your choice of 5 colors. The Titanium Jewel Threadless top also comes in your choice of size: 1.6mm, 2mm, 2.5mm, 3mm, or 4mm. This top is priced per one top only.

Specifications:

• Material: Titanium 6Al-4V-Eli ASTM F-136
• Jewel Size: 1.6mm, 2mm, 2.5mm, 3mm, or 4mm
• Works with threadless labrets that have a 0.5mm hole
• Pin Thickness: .45mm
• Pin Length: 4.5mm
• 5 Jewel color options
• 13 Anodized color options
• Threadless style
• Price per one threadless top only
• old sku: TTB-JL224

How to Use Threadless Jewelry:
Threadless jewelry uses tension between the end and the shaft to fit and stay together. The end has an insertion pin which is slightly bent when inserted into a straight shaft. This slight bend of the pin against the straight shaft creates a spring tension, holding the end securely in place. Follow the instructions below to secure the threadless end into the threadless shaft (see the image in the gallery of images for a diagram of how to use threadless jewelry)

1. Insert the pin one-third to halfway into the shaft.
2. Hand-bend slightly the insertion pin against the shaft, as shown in the gallery of images.
3. Push the end into the shaft and test the fit.

Adjusting the Fit: If it is too tight, take some of the bend out of the pin and try again. Remember, adjust slightly and then try again.

Pick-up some of these countersunk, 316L implant-grade surgical steel balls to replace missing balls for any of your 4g internally-threaded body jewelry with an internal 2mm thread pattern.

Use them on straight, circular (horseshoes), curved barbells or any other style of jewelry with a matching thread pattern and gauge.

They're made of 316L surgical stainless steel, countersunk for a perfect fit every time, and available in your choice of 8mm, 10mm, 11mm, 13mm, or 16mm sizes.

Please note that these steel balls will only work with internally-threaded body jewelry with an internal 2mm thread pattern. Each surgical steel replacement ball is sold individually

These balls will fit in either 18g or 16g because of it's 0.90mm internally threaded pattern.

Threadless Titanium Replacement Top - Prong Set Opals

0.45mm Threadless Shaft. Compatible with 0.5mm Threadless Jewelry

Change up the look of your jewelry quickly and easily

Hundreds of color and size combinations to choose from

How to Use Threadless Jewelry:

Threadless jewelry uses tension between the end and the shaft to fit and stay together. The end has an insertion pin which is slightly bent when inserted into a straight shaft. This slight bend of the pin against the straight shaft creates a spring tension, holding the end securely in place.

Follow the instructions below to secure the threadless end into the threadless shaft

1. Insert the pin one-third to halfway into the shaft.
2. Hand-bend slightly the insertion pin against the shaft.
3. Push the end into the shaft and test the fit.
4. Adjusting the Fit: If it is too tight, take some of the bend out of the pin and try again. Remember, adjust slightly and then try again.

Threadless Titanium Replacement Top - Flat Opal
0.45mm Threadless Shaft. Compatible with 0.5mm Threadless Jewelry

Change up the look of your jewelry quickly and easily
Hundreds of color and size combinations to choose from

How to Use Threadless Jewelry:

Threadless jewelry uses tension between the end and the shaft to fit and stay together. The end has an insertion pin which is slightly bent when inserted into a straight shaft. This slight bend of the pin against the straight shaft creates a spring tension, holding the end securely in place.

Follow the instructions below to secure the threadless end into the threadless shaft

1. Insert the pin one-third to halfway into the shaft.
2. Hand-bend slightly the insertion pin against the shaft.
3. Push the end into the shaft and test the fit.
4. Adjusting the Fit: If it is too tight, take some of the bend out of the pin and try again. Remember, adjust slightly and then try again.

Titanium 6Al-4V-Eli ASTM: F-136
Fits 18g and 16g internally threaded jewelry or any internally threaded jewelry with a matching internal thread pattern.

Thread length is 2mm

Thread pattern is 0.9mm

Made from 1 solid piece of material. You are only buying 1 End. You will need to buy the jewelry separately.

Beautiful handcrafted threaded tops for any internally threaded 14g piece of body jewelry. These tops are great for labrets, dermal anchors, or curves. These pieces will fit on any of our internally threaded body jewelry with a 1.2mm thread pattern.

Each piece is crafted from genuine Sterling Silver.

6mm or 8mm in diameter.

Posts (threading) is crafted from solid Titanium 6Al-4V-Eli ASTM F-136.

Choose yours below!

This product is offered at a lower price to professionals working in a studio. Please sign in or sign up for a professional account for better pricing on this and many other products in our store.