Run lower speeds than ever before while still retaining the same hitting power! Get accurate speed readings from your brush less and coil machines. 

The TattCom ESCx tattoo power supply is the most advanced power source available for your tattooing instruments. With its unique machine calibration and machine specific banks you will unlock potential you never knew your machines had.

To keep up with the ever evolving world of tattooing equipment, the ESCx tattoo power supply is equipped with Bluetooth communications to allow for wireless control as well as over the air firmware updates. 

Features

• Proprietary machine specific motor control software drivers.
• Smart start calibration starts even the hardest machines.
• Speed (hz) or Volt (v) dual modes of operation.
• 1/4"-20 threaded mount. 
• Multi-Function clamp with ballhead arm included.
• Capacitive touch buttons that will never wear out.
• Flash memory saves all user settings.
• Screen flip option allows unit to be run in multiple orientations.
• Switchcraft® locking power connector.
• Rean® all metal 1/4" machine and pedal jacks rated to 5000+ mating cycles. 
• Dual configurable I/O ports (machine/pedal)
• 5 machine calibration banks.
• 5 speed and 5 voltage presets for each calibration bank. 
• High contrast 2.4" OLED screen with wide viewing angle.
• Wireless Bluetooth® foot pedal coming soon! (sold separately)
• Mobile apps provide touch-less voice control options to reduce cross contamination.
• Over the air device firmware updates with bluetooth mobile app.
• iOS™ and Android™ devices supported.
• IP67 enclosure and sealed connectors prevent any contamination from ever reaching inside the unit.
• Dual voltage power adapter included for international operation (110/220v).
• 2 pack calibration cartridges included. 
• FCC, CE, RoHS Compliant 

With two battery slots and handy LED indicator lights, this charger offers three charging speeds to efficiently recharge your batteries. It automatically stops charging when batteries reach full capacity and resumes charging when battery voltage drops below 4.05v. Crafted with piano springs and rigorously tested for quality, this charger includes reverse polarity and short circuit protection for added safety.

Specs:

• Battery slot monitors independently
• Made with piano springs; spring tested for quality
• Reverse polarity and short circuit protection
• Three charging modes: 2A, 1A, and 0.5A
• Comes with user manual and wall charger cable
• LED light indicator battery charger with 2 ports
• Features a fire-resistant shell
• Also protects from over-discharge and over-voltage
• Auto-recharge when voltage is less than 4.05v
• Automatically shuts off when batteries are fully charged

The only power supply on the current market that allows you to use your choice of cables or connectors - wirelessly. Introducing the Airbolt, the smallest, most portable power supply that has the capabilities to keep your machine running for over 15 hours, depending on voltage. 

You can also connect the Airbolt to the Darklab app via Bluetooth to enable eGive capabilities. 

It’s time to get off the grid and experience wireless procedures.

• Up to 15 hours of battery life*
• Weighs: 3.6 oz (102 g)
• 73mm x 48 mm x 24 mm
• Built-in anti-slip magnetic pad
• For extra support, several wearable and mounting accessories will be coming soon
• Easy to bag/barrier protect
• Voice control and eGive via Darklab app

Experience the freedom and comfort that comes with a cordless foot switch. Control the ON/OFF function of Critical Connect Universal Battery or Shorty battery packs through two modes:  Continuous & Momentary. 

Features & Benefits: 

• Multi-color LED light status & battery life indicatory 
• Non-skid rubber bottom 
• Connect up to (4) Critical Connect batteries to (1) Critical Connect Foot Switch for adaptability & cordless freedom  
• Continuous & Momentary Mode Enabled 
• Critical Connect Universal Batteries are compatible & wirelessly connect with ONLY the Critical Connect Foot Switch (simultaneously, the Critical Connect Foot Switch is ONLY compatible with Critical Connect batteries)
• Can also be used with any standard clip cord 
• Size: 1” H x 5” D  
• Weight: 8.6 oz 
• 2-year manufacturer warranty 
• Made in the USA
• (2) AAA Batteries Included 
• Instruction Manual Included

The only power supply on the current market that allows you to use your choice of cables or connectors -wirelessly. Introducing the Airbolt Mini, the smallest, most portable power supply that has the capabilities to keep your machine running for up to 10 hours*.

With its intuitive controls and LED voltage display, the Airbolt is easy to use and can be paired with the Darklab app via Bluetooth for ultimate wireless control. With unlimited presets you can create within the app's Preset Bank allows artists to have endless possibilities during each session. Weighing at only 3.6 oz (102 g), the Airbolt is compact for easy travel and it’s ready to be bagged or barrier protected.

•  Weighs: 3.6 oz (102 g)
• 55.6 mm x 48 mm x 24 mm
• Up to 10 hours of battery life*
•  Built-in anti-slip magnetic pad
• Easy setup
• For extra support, several wearable and mounting accessories will be coming soon
•  eGive capabilities on the Darklab app via Bluetooth

Never set a voltage again, this is like cruise control for your brushed rotary machine. Run lower speeds than ever before while still retaining the same hitting power!

Get accurate speed readings from your brushless and coil machines. 

*Note - ESCx mode only supported on brushed rotary machines

• Proprietary machine specific motor control software drivers.
• Smart start calibration starts even the hardest machines.
• Speed (hz) or Volt (v) dual modes of operation.
• 1/4"-20 threaded mount. 
• Multi-Function clamp with ballhead arm included.
• Capacitive touch buttons that will never wear out.
• Flash memory saves all user settings.
• Screen flip option allows unit to be run in multiple orientations.
• Switchcraft® locking power connector.
• Rean® all metal 1/4" machine and pedal jacks rated to 5000+ mating cycles. 
• Dual confgurable I/O ports (machine/pedal)
• 5 machine calibration banks.
• 5 speed and 5 voltage presets for each calibration bank. 
• High contrast 2.4" OLED screen with wide viewing angle.
• Wireless Bluetooth® foot pedal coming soon! (sold separately)
• Mobile apps provide touch-less voice control options to reduce cross contamination.
• Over the air device firmware updates with bluetooth mobile app.
• iOS™ and Android™ devices supported.
• IP67 enclosure and sealed connectors prevent any contamination from ever reaching inside the unit.
• Dual voltage power adapter included for international operation (110/220v).
• 2 pack calibration cartridges included. 

Turn it on by simply holding the power button at the very top of the device.

When you turn it on, you will notice that this battery pack automatically starts at 8V. This is to jump start any machines that might need a jump start in case you are using a tighter tension membrane cartridge. 

The battery pack can operate from 4.2V up to 12V in 0.3V increments. Easily adjust the voltage on this RCA battery pack using the + or - button on the device.

When fully charged, this device allows artists to tattoo efficiently for 3–5 hours average, depending on the operating voltage being used. 

We recommend having at least 1 other battery pack on standby in the event that your battery power starts to fade during tattoo procedures

Please Note:
Always turn off the power before removing this battery pack from your tattoo machine. Failure to do so will cause the built-in failsafe to shut down the device.

To reset your battery pack, plug it into a power outlet and allow it to charge. The battery pack will become operable after approximately one hour.

The POWER UNIT IV is very versatile due to its magnetic back and bottom as well as its clip-on stand. Whether ordinary table top or suitable metal surface, the safe, comfortable hold is guaranteed. With this new tattoo power supply, it is possible for the first time to fully utilize the low-frequency operation of our SOL family. In addition, tattoo machines from other manufacturers can easily be connected via adapter cables.

The display of the POWER UNIT IV can show the stitch frequency both as a bar graph and classically via the voltage. The last set values remain stored for the continuation of the work. Foot switches can be operated in two modes for the first time. In latched mode, the foot switch for turning on and off is pressed briefly. In momentary mode the foot switch must be kept pressed during tattooing. The integrated stopwatch helps to keep track of the working time. 

THE TATTOO POWER SUPPLY FOR MORE FLEXIBILITY

• Compact tattoo power supply with focus on ergonomic, intuitive operation
• Ideal for low-frequency operation of the SOL family
• Versatile placement options thanks to powerful magnets and integrated clip-on stand
• 2 modes for foot switch operation ("latched" and "momentary")
• Voltage display (4.7 V - 12.5 V in 0.1 V steps) or bar graph display (30 steps, approx. 0.26 V per step)
• Stopwatch for measuring the time of a tattoo session
• Compatible with machines from other manufacturers via adapter (adapter is not included)
• Quality made in Germany

Unlock your peak potential using the Dotwork Box by Peak for dotwork tattooing. 

This mechanism is designed to help artists perform dotwork at their best by easily adjusting the delay speed of their machine. The delay knob at the center of the box mechanism turns both clockwise and counterclockwise to configure the rhythm and pattern of your machine on a scale of 40 up to 00.
The result? Clean dot patterns.
To use the Dotwork Box at peak level, only use with medium or hard hitting coil tattoo machines. Using the dot box with a rotary machine will damage the motor. 

Other tips for a peak-level performance: use only with tight needle groupings, alter the voltage of your machine for varied dotwork results, and adjust your tattooing speed so it matches your chosen delay speed settings. This means, you will need to tattoo faster at faster settings and more slowly at slower settings.

The Dotwork Box comes with a 1/4” mono plug to connect to a power supply that must be purchased separately. The Dotwork Box only configures the delay speed of your machine for dotwork procedures. It is not a power supply.

Your set-up can now be 100% configurable with this magnetic mounting stand for your Musotoku Power Supply!

This stand is durable, sturdy, compact, easy to set-up and easy to use. 

The stand has three magnetic feet, allowing it to be attached to any metal or otherwise magnetic surface. The magnetic feet have a powerful magnetic pull force of 30kg for stability during procedures. The threaded bolt at the end of the stand perfectly attaches to the rear nut of the Musotoku Power Supply. This stand also features a pivoting mechanism, allowing you to angle your power supply properly so that it can attach to the sides of metallic surfaces.

The Musotoku power supply works with any rotary** and coil-machine. No start-up cable is required for the Cheyenne. Thanks to the high current of Musotoku (5A), it is much easier to adjust your coil machine, and it becomes less hot even after long-term use.

Please refer to the User Manual linked below.

• Output power: 5A continous power, 10A peak. Overcurrent protection (3 types)
• Voltage: 2 to 16V, adjust in 0.1V steps, adjusting dial with infinite turns
• Setup memories: 4 auto-record memories (non-volatile)
• NITRO pulse: Fast startup (configurable)
• Footswitch model: X3 modes: Normal, Maintained and One-Touch. Pedal push detection (LED)
• Dimensions: 116X72mm, 24mm height (4.5X2.8X0.9inch)
• Weight: 169gr (5.9oz)
• Material: 2mm aircraft grade solid aluminium
• Plug: standard clipcord and footswith input 1/4inch jack
• 1 year warranty
• Made in Spain

**The LACEnano machine is known to be an exception and will not work with any standard power supply in the market either. The LACEnano, is built around a special 3-phase brushless motor and needs to be powered exclusively by the LACEnano power unit.

The Musotoku power supply works with any rotary** and coil-machine. No start-up cable is required for the Cheyenne. Thanks to the high current of Musotoku (5A), it is much easier to adjust your coil machine, and it becomes less hot even after long-term use.

Please refer to the User Manual linked below.

• Output power: 5A continous power, 10A peak. Overcurrent protection (3 types)
• Voltage: 2 to 16V, adjust in 0.1V steps, adjusting dial with infinite turns
• Setup memories: 4 auto-record memories (non-volatile)
• NITRO pulse: Fast startup (configurable)
• Footswitch model: X3 modes: Normal, Maintained and One-Touch. Pedal push detection (LED)
• Dimensions: 116X72mm, 24mm height (4.5X2.8X0.9inch)
• Weight: 169gr (5.9oz)
• Material: 2mm aircraft grade solid aluminium
• Input voltage: 19V, Worldwide compatible
• Plug: standard clipcord and footswith input 1/4inch jack
• 1 year warranty
• Made in Spain

**The LACEnano machine is known to be an exception and will not work with any standard power supply in the market either. The LACEnano, is built around a special 3-phase brushless motor and needs to be powered exclusively by the LACEnano power unit.

Powerpacks are made with leading edge battery technology weighing only 65 grams designed not to interfere with the hand more than the machine normally does.
Once the machines are rigged with Powerpacks the main unit will sense which machine is picked up and recall the settings for that machine.
High capacity batteries allows approx 5 hours of effective running time and charging takes about one hour.
Communications between the units are by radio for optimal reliability and performance.
To make the system complete, Ink Machines incorporated functions like Kickstart and Boost mode.
Kick start allows the machines to start easy and run at low voltage. Boost mode actively controls the voltage to maintain the same speed during various loads and increases the machine power significantly.
In short the RPS-600 is a complete system to control and combine your tattoo machines whether it’s a Dragonfly, Stingray or a coil machine. The RPS-600 can handle up to 6 machines with wireless Powerpacks.

Introducing the Nemesis MX2. The latest product of the Kwadron corporation.

Slimmest power supply on the market, just 18mm thick.

The glass front touch panel is very responsive.  Has a comfortable 360 degrees vice mounted on back panel. External dedicated power supply. Additional on/off switch on top of casing. Manual foot switch. 4 voltage setting programmable. And last but not least, a convenient timer so you can keep track of your time tattooing.

Voltage output range: 18VDC/2A

Voltage display and increments: 0.1V for one touch - 6.30V ; 6.40V ; 6.50V etc.

Kwadron has created a lightweight, high quality professional tattoo power supply that is packed with power. It’s compatible with both coil and rotary tattoo machines and has a hybrid latch built in, making a foot switch optional. The casing is made from a single piece of aluminum machined by CNC.

Specifications:

• Dimensions: 2.76” (L) x 3.15” (W) x 1.38”(H)
• Three digit LED display
• Adjustable voltage range 0-20V
• Voltage Input: 24VDC/ Voltage Output: 2:20VDC – max 3A
• Max power output: 24W
• Lightweight and compact with non-slip base
• Ideal for both coil and rotary tattoo machines
• External power adaptor included

Kwadron has created a lightweight, high quality professional tattoo power supply that is packed with power. It’s compatible with both coil and rotary tattoo machines and has a hybrid latch built in, making a foot switch optional. The casing is made from a single piece of aluminum machined by CNC.

Specifications:

• Dimensions: 2.76” (L) x 3.15” (W) x 1.38”(H)
• Three digit LED display
• Adjustable voltage range 0-20V
• Voltage Input: 24VDC/ Voltage Output: 2:20VDC – max 3A
• Max power output: 24W
• Lightweight and compact with non-slip base
• Ideal for both coil and rotary tattoo machines
• External power adaptor included

The Cheyenne Start Up Facility Cable is the same cable as the one comes in the PU1 and PU2 power supply. Although it was designed to use with the Cheyenne power supplies, this cable can be used to start up the Cheyenne machines with other branded power supply with ease.

This cable is 6 feet long and and features a 1/4 mono jack plug.

• *SALE* stock may have damaged boxes, but product is new
• NEW! 6 amp peak current, 4 amp true continuous current
• NEW! Pedal override button (no need for a foot pedal if you run continuous mode)
• Precision regulated set point voltage 0-18vdc
• Built in short circuit protection
• .1 volt adjustment resolution
• Voltage presets 2
• NEW! Momentary or Maintained foot switch modes. (Easy one button toggle)
• Non volatile memory (holds presets even when power is removed)
• Universal input 110-240vac 50/60hz
• Accepts standard 1/4? clip cord and foot pedal connections
• Easily bagged with typical machine or bottle baggies
• Power supply includes one magnetic universal mount
• 2 year full mfg warranty

These magnet feet will help keep your power supply in one place.  Each foot comes with a nut for a tighter fit.

The diameter of the magnet we currently have in stock is a little larger than what is pictured, but rest assured, it is not intrusive.

These magnets are quite powerful.

Great for keeping your power supply in one spot on a smooth surface. 

These 28mm x 12mm suction cups are equipped with a 3.7mm wide screw. Each suction cup comes with a 7.0mm x 7.0mm nut to ensure a tighter fit.